Last Updated: 11/18/2024 10:25 AM

MUD ROTARY DRILL RIGS FOR SALE

Ingersoll Rand RO-300
Cyclone 300R, 44R, 43R, 36R, 35R
Bucyrus Erie 40R, 30RP, 10R, 10RH

INGERSOLL RAND RO-300 DRILL RIGS  (Ref#1555Ta)  Detroit V8 engine, 11 speed transmission, 5 x 10 Gaso hydraulic mud pump, 42’ mast, 8-1/2” retractable table, 4-1/2” x 25’ fluted round kelly, hydraulic drive winch, mounted on 1980 International, 4 hyd jacks Price:  $122,500

CYCLONE RO-300  (Ref#10000R)  Manufactured 1970, 330 Ford porpane deck engine, 5-1/4" table, 3 x 4 centrfigual pump, mounted on 1973 Mack truck with 237 Cummins engine, 30' mast, sandline, no hyd pulldown, has not run in several years, good for parts or rebuilding  Price:  $36,500

CYCLONE RO-300 (Ref#1859N)  Manufactured 1975, 8" retractable table, 23-1/2' fluted kelly, mast for Range 2 casing, 8V71 Detroit engine, 600/150 LeRoi air compressor,mounted on 1975 Ford F950 tandem axle truck with Cummins diesel engine  Price:  $45,000
4-1/2 x 20' drill pipe available at extra cost

CYCLONE 300 DRILL RIG  (Ref#8929T)  3 x 4 centrifugal mud pump, Leroi piston compressor (needs work), mounted on 1999 Ford Sterling tandem axle truck with diesel engine, PTO, rod box, 4 hydraulic leveling jacks, 100’ of 3-1/2” x 20’ drill pipe  Price:  $62,500

CYCLONE 300 DRILL RIG  (Ref#373T)  Manufactured 1973, 871 Detroit diesel on deck, 450 cfm Bendix Westinghouse air compressor, no mud pumps but hydraulics are there, 4” kelly, 8” retractable table, bailing line, hydraulic winch, mounted on 1972 Ford F900 tandem axle truck with 434 gas engine, 3 hydraulic jacks, 200’ of 4-1/2” x 15’ drill pipe, sitting since 2019  Price:  $37,500

CYCLONE 300 (Ref#5693R) Manufactured mid 1970's, Ford 300 industrial deck engine, mounted on 1985 Ford 600 (not 4x4) with 429 gas engine, 4 x 3 Mission mud pump, Leroi developmental air compressor, 5 ¼" retractable table, 3-1/2" x 19' Kelly, hydraulic pulldown, mechanical clutches, 300 gallon mud pit with mixer & hoses, breakout wrench, rod box, 200' of 2 3/8" IF x 15' drill pipe, bits & subs, 3 hydraulic leveling jacks, ready to go    PRICE:  $45,000

CYCLONE T10 DRILL RIG  (Ref#10916T)  Gardner Denver 5 x 6 mud pump, 12” kelly and a smaller diameter kelly, 3’ table, 30’ mast, single drum, mounted on 1977 International 1850 truck with Cat 3208 engine, PTO, 13 speed Fuller transmission, leveling jacks, (10) 4-1/2” x 21’ drill pipe, used for large diameter and small diameter wells for irrigation, manual/parts book, not used for several years  Price:  $65,000

CYCLONE 44R  (Ref#1509), Manufactured 1970 - combination mud rotary and cable rig,  Ford 6 cylinder gasoline engine on deck, 5 x 6 GD duplex mud pump, 34' mast, 3 hydraulic leveling jacks,  Mounted on tandem axle truck, Diamond Reo powered by Cummins 220 diesel engine,  3" x 24' kelly, 2-3/8" x 20' drill pipe, 13'H x 8'W x 34'L, handling equipment, table bushings, tools  Price:  $45,000

CYCLONE 43R COMBINATION CABLE/KELLY (Ref#4485)  12" x 600' capacity, Mounted on tandem axle Mack truck, 4 x 5 GD mud pump, 38' mast, 6 cyl gas Ford 300 engine runs drawworks and pump, Large rotary table, hydraulic leveling jacks  Price to be determined

CYCLONE 42R ROTARY/CABLE COMBINATION RIG  (Ref#5173N)  Ford Industrial gas deck engine, mounted on 1972 Kaiser 6 x 6 truck with 6 cyl Turbo diesel engine, (both engines rebuilt), 5" stationary table, 4" x 12' square kelly, King swivel, portable mud pit, 5" and 6" tools, no mud or air, no leveling jacks, no pipe  Price:  $45,000

SANDERSON CYCLONE 36R COMBINATION ROTARY/SPUDDER RIG  (Ref#11403Tb)  4 cylinder Ford diesel engine on deck, 38' hydraulically raised mast, 5-1/2" table retractable to 18" x 12" deep, 3-1/2" x 20' fluted Kelly, drill line drum, sandline drum and casing drum (no line on rig).  2-part block, shock in the crown for cable drilling,  Mounted on 1992 Ford L7000 all-wheel drive truck with 6 cyl Ford diesel engine, automatic transmission with big hydraulic pump, low miles, 3 hydraulic leveling jacks, needs new hoses and swivel, no rod box.  Price:  $32,500 – Oklahoma

SANDERSON CYCLONE (Ref#15013T)  4 cyl Red Seal Continental gas deck engine, 2 line machine, shortened mast, mounted on 2-1/2 ton Military 6x6 truck with gas engine, no jacks, well maintained, last worked 2021 but starts it up.  Includes a Cyclone 42 on old Chevy for parts  Price:  $37,500 – Ohio
Tools available at extra cost

CYCLONE 36R COMBINATION CABLE TOOL/KELLY PARTS RIG  (Ref#3999N)  Manufactured 1981, 4 x 3 Mission, White diesel deck engine, developmental air compressor, 5" retractable table, fluted kelly, Bean water injection pump, mounted on 1981 Ford (not 4x4) with diesel engine, bailing line, sandline, casing line, 4 hydraulic jacks, pulldown, mechanical clutches, truck does not run, sitting over 10 years  Price:  $14,500 - Michigan

CYCLONE 36 COMBINATION CABLE TOOL/TABLE DRIVE DRILLING RIG  (Ref#2328Ta)  Gardner Denver 5 x 6 mud pump with auxiliary engine, 5 cylinder deck engine, mounted on Ford truck with propane engine, retractable table, 1 front and 2 rear hydraulic leveling jacks (hydraulics redone), no rod box, no pipe rack, no drill pipe  Price on Request - Florida

CYCLONE 36R (Ref#3980N) combination cable/Kelly rig, manufactured 1960’s, (2) Ford gas deck engines, mounted on 1987 Freightliner with Cat engine, 3x4 Mission mud pump (not on rig but available), 18’ Kelly, 5 1/4” retractable table, hydraulic pulldown, mechanical clutches, mud pit, cone desander, pipe rack (removed from available), 200’ of 2 7/8” x 15’ drill pipe, breakout wrench, hydraulic leveling jacks, 4” & 6” cable tools  Price on Request – Michigan

CYCLONE 36R COMBINATION CABLE/TABLE DRIVE DRILL RIG  (Ref#7661Tb)  Gardner Denver 5 x 6 mud pump w/4 cyl John Deere engine, no air, 172 Industrial Ford gas deck engine, 5-1/4” retractable table, mounted on GMC tandem axle truck with gas engine, 3 hydraulic leveling jacks, pipe rack, 180’ drill pipe  Price:  $27,500

CYCLONE 36R COMBINATION RIG  (Ref#11157)  2 Ford Industrial engines (one runs rig and one runs pump), mounted on 1964 International tandem truck with 220 Cummins, 5-1/2 x 6 Gardner Denver pump, 18' kelly, 5-1/4" retractable table, 2" swivel, 4" spudder tools, 375 gal attached swing-up mud pan, 180' of  Mayhew regular pipe  Price:  47,500

CYCLONE 36R (Ref#9430T)  Currently being rebuilt, 38' extended mast, Cummins 4BT deck engine, new 4 x 3 Mission mud pump, 8-1/2" Franks table, all new hydraulics, currently unmounted with no air compressor  POR

CYCLONE 35R  (Ref#6558T)  5" Gardner Denver mud pump with 3 cyl diesel engine, no air, square kelly, retractable table, hydraulic pulldown, pipe rack, 4 cylinder diesel deck engine, mounted on 1985 Mack twin screw with diesel engine, 3 hyd leveling jacks, 300' of 2" x 16' drill pipe  Price:  $64,500

CYCLONE 35R COMBINATION MUD ROTARY CABLE TOOL RIG  (Ref#10514T)  Built 1966, 5 x 6 mud pump, developmental air compressor, mounted on 1966 Ford F950 Super Duty with gas engine, (2) gas deck engines (one runs rig, one runs air compressor and mud pump), 240' drill rod, 15' sub and bit  Price:  $29,500

CYCLONE 35R COMBINATION RIG  (Ref#2400N)  4 cyl Ford gas deck engine, mounted on 1988 Ford F800 single axle truck, rebuilt 5-1/4” retractable table, Bean water injection, 10’ stabilizer, 3 hydraulic leveling jacks, 240’ of 2-7/8” x 20’ Mayhew Jr pipe, currently drilling, will be available Summer 2024    Price:  $62,500
pull behind compressor available at extra cost

CYCLONE 35R  (Ref#483N)  Manufactured 1969, Gardner Denver 3 x 2-1/2" pump (needs new pistons), mounted on 1977 International truck with DT466, 400' of 2-3/8 Mayhew Jr., stabilizers  Price:  $35,000

BUCYRUS ERIE 30RT  (Ref#13547)  220 Cummins deck engine, mounted on Crane Carrier with Red Diamond 6 cyl gas engine, 5 & 3 speed transmission, tools  Price:  $20,000

BUCYRUS ERIE 10R  (Ref#11705T)  Manufactured 1973, 5 x 6 Gardner Denver mud pump (new pistons and liners 2016), 50 SDS air compressor, bailing drum, 24’ kelly, 8-1/4” retractable table, hydraulic pulldown, air clutches, mounted on 1989 Chevy Topkick with Cat 3208T, rod box, 300’ of 3” drill stem, tools, well maintained  Price:  $47,500  Additional pipe available at extra cost.

BUCYRUS ERIE 10R  (Ref#13653T)  Manufactured 1972, 1500 drawworks, 5 x 6 mud pump, 680 cfm air compressor, 3-5/16" x 23' kelly (also a spare kelly), new stabilizer, breakout wrench, Myers water injection, 30' mast, 7-1/2" retractable table, pipe rack, mounted on 972 Ford L8000 truck with Cat 3208 engine, 3 hyd leveling jacks, 15 jts of 3-1/2" x 15' drill pipe (2-7/8 IF)  Price:  $52,500

BUCYRUS ERIE 10R  (Ref#1402Ta)  Midway 1500 drawworks with 16" air cutches, 8-1/2" Midway rotary table operated by 8" twin disc clutch, Pullmaster hydraulic make up cathead, 45' derrick rigged up on 4 lines with King G53A swivel, 39' x 4-1/4" kelly, Detroit 6V71 Detroit deck engine, mounted on 1981 Western Star engine with Big Cam 400 Cummins engine, 10 speed transmission
Includes Gardner Denver FXZ 7-1/4 x 12 mud pump with 61381 Allis Chalmers 450 hp engine, air start, pump drive, belt guard, surge dampener, 500 gallon fuel tank mounted on tandem axle drop deck trailer
1,200' of 3-1/2 IF 13.30 drill pipe, (9) 4-1/2" drill collars on tandem trailer
Doghouse 6' x 12' with drillograph and tools
Price:  $49,500

BUCYRUS ERIE 10R (Ref#1986Nc) Manufactured 1972, PTO, mounted on 1972 Ford F8000 with Cat 3208 engine, 5x6 piston mud pump, Leroi 50SDS air compressor, 8" retractable table, 5 ¼" table bushing, Myers water injection pump, line oiler, sandline, pipe rack, breakout wrench,  new water swivel, 40000# mast capacity, 16000# pulldown, mud pan, mud mixer, 1 front & 2 rear hydraulic leveling jacks, 270' of 2 7/8" OD x 20' drill pipe, 2 3/8" IF  Price on request

BUCYRUS ERIE 10R  (Ref#14627)  Manufactured 1972, mounted on 1972 Ford truck, 300' of 3-1/2" x 15' drill pipe, 5 x 8 mud pump, small LeRoi compressor, rebuilt  Price:  $75,000

BUCYRUS ERIE 10R  Ref#826N)  Manufactured 1970's, mounted on International Paystar truck, 3 line machine, Detroit 6V71 engine, PTO, no tools    PRICE:  $65,000

BUCYRUS ERIE 10R (Ref#8962R) Manufactured 1970, 38’ mast, 5 x 6 Gardner Denver mud pump, 50 SDS air compressor, 2 line, 8-1/4” retractable rotary table, water injection, mounted on 1968 White 9000 with 250 Cummins engine, 13 speed transmission, 225’ of 3-1/2” with 2-3/8 IF pipe, sitting a few years, running when parked Price: $52,500
Available at extra cost: 1996 INTERNATIONAL 4700 WATER TRUCK (Ref#8962Rb) 1400 gal water tank, DT466, 6 speed Price: $21,500

BUCYRUS ERIE 10R  (Ref#7203N)  650/250 air compressor, no mud, 6 cyl Detroit on deck, mounted on 1978 Kenworth truck, 8V71 Detroit, water injection, no pipe or tools  Price:  $42,500

BUCYRUS ERIE 10R  (Ref#2083N)  Manufactured 1970's, 450/250 LeRoi air compressor, 6V71 Detroit deck engine, 8-1/2" retractable table, mechanical clutches, hydraulic pulldown, sandline, water injection, 23' kelly,  no pipe rack, no rod box, (15) 4-1/2" FJ x 15' drill rod, 3 hyd leveling jacks, needs new truck   Price:  $30,000

BUCYRUS ERIE 10RH  (Ref#1161)  2 available - 500/250 air compressor, 671 Detroit diesel, mounted on Ford 750 tandem axle truck with gas engine, 23' x 4" kelly, parts, 400' of 4" x 20' drill pipe, (1) manufactured 1968 good condition, (1) manufactured 1963 needs work      Price for both:  $34,500

BUCYRUS ERIE 10RH  (Ref#5709)  Manufactured 1968,parts rig 

BUCYRUS ERIE 10R  (Ref#1847N)  23' fluted kelly, table drive, LeRoi 450/250 air compressor, Mission 4 x 3 pump, mounted on Ford F800 tandem axle truck with gas engine, needs deck engine, hyd pump and rebuilding  Price:  $28,000

BUCYRUS ERIE 10R  (Ref#1502N)  (2) 5 x 6 mud pumps, (1) 3 x 4 Mission Magnum centrifugal pump (low hours), mounted on Crane Carrier, Detroit diesel engine, PTO, hydraulic pulldown, mechanical clutches, retractable table, 3-1/2" x 23' kelly, breakout wrench, good condition, currently drilling, 155' of 3-1/2" pipe, 200' of 20' stems  Price:  $65,000

BUCYRUS ERIE 10R  (Ref#14720Tb)  parts rig

BUCYRUS ERIE 10R  (Ref#13101Rd) only derrick, kelly bar, turntable, in pieces POR